To ensure that guitar amplifiers produce the desired tone, they should be maintained regularly by experienced and qualified technicians. Consistent maintenance enables your amplifier to have a long life and high resell value. Repairing and preventive maintenance will cost less than purchasing a new one. Some of the tips on guitar amplifier repair one can use are discussed below.
Check the filter caps occasionally and determine whether they are working as expected. In the event that they are not in the best condition, replace them with new ones. When not replaced in time, they may cause the music equipment to break down during work. This can bring confusion and disharmony with the other instruments comprising of the band. The big caps are ones that get faulty frequently. Be checking on them frequently and replace them when necessary to avoid failure.
Tube sockets must be tightened all the time. As you continually use the amplifier, the tube sockets loosen up over some time and start causing your amplifier to produce hissing and sizzling sounds. To curb this, you can either hire a technician to tighten them or do it for yourself by keenly using screwdrivers. Kindly take care because there is high voltage present which can make you encounter electric shock inadvertently.
The scratchy pot should be kept in clean at all time. When it is cloaked with dirt, it can make your amplifier to go silent abruptly. Some dust, cobwebs, dodgy wires and insect carcasses get stuck in the pot and it is imperative to wash it with a squirt cleaner on frequent basis.
All the bolts, nuts and screws appearing at the back panel, power transformers and mounts on the chassis should be tightened. When these bolts, nuts and screws are left loose, they make the amplifier vibrate intensely hence lowering the quality of tone produced by the instrument. This task can be achieved by using a toolkit with screwdrivers.
Resistors will wear out and some other times fail in older amplifiers. Therefore, there is a need to replace them occasionally. When they are not replaced the amplifier will start producing sizzling and hissing sounds. One particular resistor that requires to be replaced more often is the 100k ohms comp resistor in the preamp stages of vintage fender amps.
Also, large resistors on the power stage wear out frequently because of the high voltage and heat which they have to deal with. They also have to be checked regularly and replaced with new ones to avoid any anomalies. The replacement of the resistors should be done by experienced technician to avoid more damage.
More importantly, determine the state of the tone circuit and coupling capacitors. To avoid short circuiting the entire equipment, please inquire from an expert about capacitors. It may be necessary to replace the faulty capacitors with the new ones. Make sure these match the ratings of the circuit.
Check the filter caps occasionally and determine whether they are working as expected. In the event that they are not in the best condition, replace them with new ones. When not replaced in time, they may cause the music equipment to break down during work. This can bring confusion and disharmony with the other instruments comprising of the band. The big caps are ones that get faulty frequently. Be checking on them frequently and replace them when necessary to avoid failure.
Tube sockets must be tightened all the time. As you continually use the amplifier, the tube sockets loosen up over some time and start causing your amplifier to produce hissing and sizzling sounds. To curb this, you can either hire a technician to tighten them or do it for yourself by keenly using screwdrivers. Kindly take care because there is high voltage present which can make you encounter electric shock inadvertently.
The scratchy pot should be kept in clean at all time. When it is cloaked with dirt, it can make your amplifier to go silent abruptly. Some dust, cobwebs, dodgy wires and insect carcasses get stuck in the pot and it is imperative to wash it with a squirt cleaner on frequent basis.
All the bolts, nuts and screws appearing at the back panel, power transformers and mounts on the chassis should be tightened. When these bolts, nuts and screws are left loose, they make the amplifier vibrate intensely hence lowering the quality of tone produced by the instrument. This task can be achieved by using a toolkit with screwdrivers.
Resistors will wear out and some other times fail in older amplifiers. Therefore, there is a need to replace them occasionally. When they are not replaced the amplifier will start producing sizzling and hissing sounds. One particular resistor that requires to be replaced more often is the 100k ohms comp resistor in the preamp stages of vintage fender amps.
Also, large resistors on the power stage wear out frequently because of the high voltage and heat which they have to deal with. They also have to be checked regularly and replaced with new ones to avoid any anomalies. The replacement of the resistors should be done by experienced technician to avoid more damage.
More importantly, determine the state of the tone circuit and coupling capacitors. To avoid short circuiting the entire equipment, please inquire from an expert about capacitors. It may be necessary to replace the faulty capacitors with the new ones. Make sure these match the ratings of the circuit.
About the Author:
For the most professional guitar amplifier repair service customers can search locally or online. We highly recommend this website at http://www.musictechnology.com for all your music tuning needs.
0 nhận xét: